| |
|
| |
|
| |
|
| C021 |
Developer unit motor-YMC locking error: The developer unit motor-YMC is not rotating normally. |
| C022 |
Developer unit mixer motor-YMC locking error: The developer unit mixer motor-YMC is not rotating normally |
| C023 |
Developer unit motor-K locking error: The developer unit motor-K is not rotating normally. |
| C024 |
Developer unit mixer motor-K locking error: The developer unit mixer motor-K is not rotating normally. |
| C130 |
1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 1st drawer) |
| C140 |
2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 2nd drawer) |
| C150 |
3rd drawer tray abnormality: The 3rd drawer tray-up motor is not rotating or the 3rd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 3rd drawer) |
| C160 |
4th drawer tray abnormality: The 4th drawer tray-up motor is not rotating or the 4th drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 4th drawer) |
| C180 |
LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF) |
| C1A0 |
LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF) |
| C1C0 |
Option LCF tray-up motor abnormality: The option LCF tray-up motor is not moving normally |
| C260 |
Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON. |
| C270 |
(1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time. (2) Downloading firmware with an incorrect model. |
| C280 |
Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time. |
| C360 |
Needle electrode cleaner operation abnormality |
| C370 |
Transfer belt operation abnormality |
| C380 |
Auto-toner sensor-K abnormality (upper limit) |
| C381 |
Auto-toner sensor-K abnormality (lower limit) |
| C382 |
Auto-toner sensor-K connection error |
| C390 |
Auto-toner sensor-C abnormality (upper limit) |
| C391 |
Auto-toner sensor-C abnormality (lower limit) |
| C392 |
Auto-toner sensor-C connection error |
| C3A0 |
Auto-toner sensor-M abnormality (upper limit) |
| C3A1 |
Auto-toner sensor-M abnormality (lower limit) |
| C3A2 |
Auto-toner sensor-M connection error |
| C3B0 |
Auto-toner sensor-Y abnormality (upper limit) |
| C3B1 |
Auto-toner sensor-Y abnormality (lower limit) |
| C3B2 |
Auto-toner sensor-Y connection error |
| C3C0 |
Process unit connection error |
| C411 |
Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser belt does not rise in a specified period of time after power is turned ON. |
| C412 |
Thermistor/heater lamp abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser belt temperature does not rise within a specified period of time after power-ON. |
| C443 |
Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature) |
| C445 |
Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality) |
| C446 |
Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality) |
| C447 |
Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status) |
| C448 |
Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified |
| C451 |
Thermopile and edge thermistor temperature difference |
| C452 |
Thermopile temperature difference |
| C461 |
Pressure roller heater 40°C detection (Not determined) |
| C462 |
Pressure roller heater 40°C detection (Determined) |
| C463 |
Pressure roller thermistor and edge thermistor temperature difference |
| C464 |
Pressure roller thermistor temperature difference |
| C465 |
Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| C466 |
Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| C467 |
Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status) |
| C468 |
Pressure roller thermistor abnormality after entering ready status (overheating) |
| C471 |
IH board initialization abnormality |
| C472 |
Power supply abnormality |
| C473 |
Surge pressure detection / power and voltage upper limit abnormality |
| C474 |
Power and voltage lower limit abnormality |
| C476 |
IH low power supply |
| C480 |
IGBT high temperature abnormality |
| C481 |
IH drive circuit abnormality |
| C490 |
IH circuit abnormality / IH coil abnormality |
| C4B0 |
Fuser unit counter abnormality |
| C4B1 |
Fuser unit voltage judgment abnormality |
| C4D0 |
Fuser belt thermopile abnormality |
| C4E0 |
Fuser unit releasing operation abnormality - Though the pressure roller is released, its position cannot be detected. |
| C4E1 |
Fuser unit contacting operation abnormality - Though the pressure roller is contacted, its position cannot be detected. |
| C4E2 |
Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates. |
| C4E3 |
Fuser motor rotation abnormality |
| C550 |
RADF I/F error: Communication error has occurred between the RADF and the scanner. |
| C560 |
Communication error between Engine-CPU and PFC board |
| C570 |
Communication error between Engine-CPU and CNV board |
| C580 |
Communication error between CNV board and finisher |
| C5A0 |
SRAM board not connected (LGC board) |
| C5A1 |
SRAM board data abnormality (LGC board) |
| C730 |
RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed. |
| C880 |
RADF original feed motor abnormality: An error signal has been detected when the motor is rotating. |
| C890 |
RADF read motor abnormality: An error signal has been detected when the motor is rotating. |
| C8A0 |
RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating. |
| C8B0 |
RADF original exit motor abnormality: An error signal has been detected when the motor is rotating. |
| C8C0 |
RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed, but is ended unsuccessfully. |
| C8E0 |
RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred. |
| C900 |
Connection error between SYS board and LGC board |
| C940 |
Engine-CPU abnormality |
| C962 |
LGC board ID abnormality |
| C970 |
High-voltage transformer abnormality: Leakage of the main charger is detected. |
| C9E0 |
Connection error between SLG board and SYS board |
| CA00 |
Image position alignment abnormality |
| CA10 |
Polygonal motor abnormality: The polygonal motor is not rotating normally |
| CA20 |
H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams. |
| CA47 |
SNS board abnormality: The SNS board does not operate due to disconnection or the harness breaking. |
| CB00 |
Finisher not connected: Communication error has occurred between the equipment and finisher. [MJ1103/1104] |
| CB01 |
Finisher communication error: Communication error has occurred between the equipment and finisher. [MJ-1103/1104] |
| CB10 |
Entrance motor abnormality: The entrance motor is not rotating normally. [MJ-1103/1104] |
| CB11 |
Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1103/1104] |
| CB12 |
Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1103/1104] |
| CB13 |
Finisher exit motor abnormality |
| CB14 |
Paper holding arm motor abnormality |
| CB30 |
Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally. [MJ-1103/1104] |
| CB31 |
Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. [MJ-1103/1104] |
| CB40 |
Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally. [MJ-1103/ 1104] |
| CB50 |
Stapler home position error: The stapler home position sensor does not work. [MJ-1103/1104] |
| CB51 |
Stapler shift home position error: The stapler is not at the home position. [MJ-1103/1104] |
| CB60 |
Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally. [MJ-1103/1104] |
| CB80 |
Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON |
| CB81 |
Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1103/1104] |
| CB82 |
Finisher - Main CPU program error |
| CB83 |
Saddle Stitch Finisher - Main CPU program error |
| CB84 |
Hole Punch Unit - Main CPU program error |
| CB91 |
Saddle Stitch Finisher flash ROM abnormality |
| CB92 |
Saddle Stitch Finisher RAM abnormality |
| CB93 |
Additional folding motor abnormality |
| CB94 |
Saddle transport motor abnormality |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC73 |
Punching device power supply abnormality |
| CC74 |
Punch unit transport pulse abnormality |
| CC80 |
Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally. [MJ-1103/1104] |
| CD60 |
Sub-hopper toner sensors abnormality. |
| CD61 |
Sub-hopper toner motor-Y abnormality. |
| CD62 |
Sub-hopper toner motor-M abnormality. |
| CD63 |
Sub-hopper toner motor-C abnormality. |
| CD64 |
Sub-hopper toner motor-K abnormality. |
| CD71 |
Waste toner transport motor locking error: The auger in the waste toner transport path does not rotate. |
| CD80 |
TRU waste toner motor locking error: The auger (TRU side) in the TRU waste toner transport path does not rotate. |
| CD81 |
TRU waste toner transport motor locking error: The auger (waste toner box side) in the TRU waste toner transport path does not rotate. |
| CD82 |
TRU waste toner full-status error |
| CDE0 |
Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally. [MJ1103/1104] |
| CE00 |
Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board [MJ-1103/1104 (when MJ-6102 is installed)] |
| CE10 |
Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF. |
| CE20 |
Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed. |
| CE40 |
Image quality control test pattern abnormality: The test pattern is not formed normally. |
| CE41 |
Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally. |
| CE42 |
Image quality TRC control test pattern abnormality (EFI printer board): Image quality TRC control test pattern is not printed normally. |
| CE50 |
Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range. |
| CE60 |
Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range. |
| CE71 |
Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time. |
| CE90 |
Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range. |
| CEC0 |
2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally. |
| CF10 |
Communication module SRAM reading failure. |
| CF90 |
Laser optical unit shutter abnormality. |
| CFA0 |
Media sensor output abnormality before paper reaching: The sensor output value before paper is reached to the media sensor is not normal. |
| CFA1 |
Media sensor output abnormality during paper passing: The sensor output value while paper is being passed is not normal. |
| E010 |
Jam not reaching the fuser transport sensor The paper which has passed through the fuser unit does not reach the fuser transport sensor. |
| E011 |
Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor. |
| E020 |
Stop jam at the fuser transport sensor: The trailing edge of the paper does not pass the fuser transport sensor after its leading edge has reached this sensor. |
| E030 |
Power-ON jam: The paper is remaining on the paper transport path when power is turned ON. |
| E061 |
Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment. |
| E062 |
Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment. |
| E063 |
Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment. |
| E064 |
Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment. |
| E065 |
Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment. |
| E071 |
1st drawer media type mis-setting jam: The media type setting of the 1st drawer is incorrect. |
| E072 |
2nd drawer media type mis-setting jam: The media type setting of the 2nd drawer is incorrect. |
| E073 |
3rd drawer media type mis-setting jam: The media type setting of the 3rd drawer is incorrect. |
| E074 |
4th drawer media type mis-setting jam: The media type setting of the 4th drawer is incorrect. |
| E075 |
Option LCF media type mis-setting jam: The media type setting of the option LCF is incorrect. |
| E076 |
Tandem LCF media type mis-setting jam: The media type setting of the tandem LCF is incorrect. |
| E090 |
Image data delay jam: Image data to be printed cannot be prepared. |
| E091 |
Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware. |
| E0A0 |
Image transport ready time-out jam: Image data to be printed cannot be sent. |
| E110 |
ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing. |
| E120 |
Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor. |
| E130 |
1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor. |
| E140 |
2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor. |
| E150 |
3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor |
| E160 |
4th drawer misfeeding (Paper not reaching the 4th drawer feed sensor): The paper fed from the 4th drawer does not reach the 4th drawer feed sensor. |
| E180 |
Option LCF misfeeding (Paper not reaching the LCF feed sensor): Paper fed from the LCF does not reach the LCF feed sensor. |
| E190 |
LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor. |
| E200 |
1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor. |
| E210 |
2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor. |
| E220 |
2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor. |
| E230 |
1st drawer misfeeding (Paper not reaching the 1st drawer transport sensor): Paper fed from the 1st drawer does not reach the 1st drawer transport sensor. |
| E240 |
2nd drawer misfeeding (Paper not reaching the 2nd drawer transport sensor): Paper fed from the 2nd drawer does not reach the 2nd drawer transport sensor. |
| E260 |
Option LCF transport jam (Paper not reaching the registration sensor) |
| E270 |
Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor. |
| E290 |
Option LCF transport jam: Paper fed from the Option LCF does not reach the 1st drawer transport sensor. |
| E2B0 |
Stop jam at the registration sensor (1st drawer) |
| E2B1 |
Stop jam at the registration sensor (2nd drawer) |
| E2B2 |
Stop jam at the registration sensor (3rd drawer) |
| E2B3 |
Stop jam at the registration sensor (4th drawer) |
| E2B4 |
Stop jam at the registration sensor (Bypass tray) |
| E2B5 |
Stop jam at the registration sensor (LCF) |
| E2B6 |
Stop jam at the registration sensor (ADU) |
| E2B7 |
Stop jam at the registration sensor (option LCF) |
| E300 |
3rd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor. |
| E310 |
3rd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor. |
| E320 |
3rd drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor. |
| E330 |
4th drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor. |
| E340 |
4th drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor. |
| E350 |
4th drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor. |
| E360 |
4th drawer transport jam (Paper not reaching the 3rd drawer feed sensor): The paper does not reach the 3rd drawer feed sensor after it has passed the 4th drawer feed sensor. |
| E370 |
3rd drawer misfeeding (Paper not reaching the 3rd drawer transport sensor): Paper fed from the 3rd drawer does not reach the 3rd drawer transport sensor. |
| E380 |
4th drawer misfeeding (Paper not reaching the 4th drawer transport sensor): Paper fed from the 4th drawer does not reach the 4th drawer transport sensor. |
| E3C0 |
LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor. |
| E3D0 |
LCF transport jam (Paper not reaching the 1st drawer feed sensor): Paper fed from the LCF and passed through the 2nd drawer feed sensor does not reach the 1st drawer feed sensor. |
| E3E0 |
LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor. |
| E3F0 |
Tandem LCF misfeeding (Paper not reaching the tandem LCF feed sensor): Paper fed from the Tandem LCF does not reach the tandem LCF transport sensor. |
| E400 |
Duplexing unit open jam |
| E430 |
ADU open jam: The ADU has opened during printing. |
| E440 |
Paper feed cover open jam: The paper feed cover has opened during printing. |
| E450 |
LCF side cover open jam: The LCF side cover has opened during printing. |
| E480 |
Bridge unit open jam: The bridge unit has opened during printing. |
| E4A0 |
Waste toner cover open jam (printing) |
| E4B0 |
Bridge unit open jam (printing): The bridge unit has opened during printing. |
| E510 |
Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section. |
| E511 |
ADU misfeeding (Paper not reaching the ADU transport sensor-1) |
| E540 |
ADU misfeeding (Paper not reaching the ADU feed sensor): Paper does not reach the duplexing unit path exit sensor after it has passed the duplexing unit path entrance sensor. |
| E550 |
Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding). |
| E570 |
Jam not reaching the bridge unit. |
| E580 |
Stop jam at the bridge unit |
| E590 |
Jam not reaching the upper paper exit sensor |
| E5A0 |
Stop jam at the upper paper exit sensor |
| E712 |
Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor. |
| E714 |
Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray. |
| E721 |
Jam not reaching the original reading start sensor: The original does not reach the reading start sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side). |
| E722 |
Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section. |
| E724 |
Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor. |
| E725 |
Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor. |
| E726 |
Transport/exit signal reception jam during ADF standby status |
| E727 |
Jam not reaching the original reading end sensor |
| E729 |
Stop jam at the original reading end sensor |
| E731 |
Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor. |
| E744 |
Stop jam at the exit/reverse sensor |
| E745 |
Jam not reaching the exit reverse sensor |
| E746 |
Exit/reverse sensor paper remaining jam |
| E762 |
Registration sensor paper remaining jam |
| E770 |
Original width detection sensor-1 paper remaining jam |
| E771 |
Original width detection sensor-2 paper remaining jam |
| E772 |
Original width detection sensor-3 paper remaining jam |
| E773 |
Intermediate transport sensor paper remaining jam |
| E774 |
Reading start sensor paper remaining jam |
| E775 |
Reading end sensor paper remaining jam |
| E777 |
Exit sensor paper remaining jam |
| E860 |
Original jam access cover open: The Original jam access cover has opened during RADF operation. |
| E870 |
RADF open jam: RADF has opened during RADF operation. |
| E871 |
Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment. |
| E910 |
Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor. |
| E920 |
Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor. |
| E930 |
Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1. |
| E940 |
Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2. |
| E970 |
Jam not reaching the lower paper exit sensor: Paper transported from the bridge unit does not reach the lower paper exit sensor. |
| E980 |
Stop jam at the lower paper exit sensor: Paper transported from the bridge unit does not pass the lower paper exit sensor. |
| E9F0 |
Punching jam: Punching is not performed properly. [MJ-1103/1104 (when MJ-6102 is installed)] |
| EA10 |
Paper transport delay jam: The paper which has passed the relay transport path does not reach the inlet sensor. [MJ-1103/1104] |
| EA20 |
Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ1103/1104] |
| EA21 |
Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec. [MJ-1103/1104] |
| EA22 |
Paper transport jam (Finisher paper punching edge detection sensor): [MJ-1103/1104] |
| EA23 |
Paper transport jam (exit sensor): [MJ-1103/1104] |
| EA24 |
Paper transport jam (between entrance and exit sensors): [MJ-1103/1104] |
| EA25 |
Paper transport jam (after paper stack exit): [MJ1103/1104] |
| EA26 |
Paper transport jam (stop command request): [MJ1103/1104] |
| EA27 |
Paper transport jam (paper not inserted): [MJ-1103/ 1104] |
| EA28 |
Paper transport jam (assisting arm operation delay): [MJ-1103/1104] |
| EA29 |
Paper transport jam (stack transport delay): [MJ1103/1104] |
| EA31 |
Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ-1103/1104] |
| EA32 |
Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON. [MJ-1103/1104] |
| EA40 |
Door open jam: The upper/front cover of the finisher section or the upper/ front door of the puncher section has opened during printing. [MJ-1103/1104] Cover open error: The front cover or stationary tray cover is opened during paper transport. [MJ-1103/1104] |
| EA50 |
Stapling jam: Stapling is not performed properly. [MJ-1103/1104] |
| EA60 |
Early arrival jam: The inlet sensor detects the paper earlier than a specified timing. [MJ-1103/1104] |
| EA70 |
Stack exit belt home position error: The stack exit belt is not at the home position. [MJ-1103/1104] |
| EA90 |
Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1103/1104]. |
| EAA0 |
Power-ON jam: Paper exists at No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1103/1104] |
| EAB0 |
Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor or delivery sensor. [MJ-1103/1104] |
| EAB1 |
Short paper jam (Saddle Stitch Finisher) |
| EAD0 |
Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing. |
| EAE0 |
Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher. |
| EB30 |
Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing. |
| EB50 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper. |
| EB60 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]). |
| ED10 |
Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1103/1104 (when MJ-6102 is installed)] |
| ED11 |
Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1103/1104 (when MJ6102 is installed)] |
| ED12 |
Shutter home position error: The shutter is not at the home position. [MJ-1103/1104] |
| ED13 |
Front alignment plate home position error: The front alignment plate is not at the home position. [MJ1103/1104] |
| ED14 |
Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ1103/1104] |
| ED15 |
Paddle home position error: The paddle is not at the home position. [MJ-1103/1104] |
| ED16 |
Buffer tray home position error: The buffer tray is not at the home position. [MJ-1103/1104] |
| EF10 |
Paper not supported for Saddle Stitch Finisher |
| EF11 |
Saddle Stitch Finisher stapling error (front) |
| EF12 |
Saddle Stitch Finisher stapling error (rear) |
| EF13 |
Saddle paper holder home position detection abnormality |
| EF14 |
Saddle paper exit jam |
| EF15 |
Saddle Stitch Finisher side alignment motor home position detection abnormality |
| EF16 |
Saddle Stitch Finisher stacker motor home position detection abnormality |
| EF17 |
Saddle Stitch Finisher folding blade home position detection abnormality |
| EF18 |
Saddle Stitch Finisher additional folding roller home position detection abnormality |
| EF19 |
Saddle paper folding jam |
| EF20 |
Saddle stacker jam |
| EF21 |
Hole Punch Unit paper leading edge skew detection abnormality |
| EF22 |
Hole Punch Unit paper leading edge detection abnormality |
| EF23 |
Hole Punch Unit paper alignment abnormality |
| EF24 |
Hole Punch Unit paper trailing edge skew detection abnormality |
| EF25 |
Hole Punch Unit paper trailing edge detection abnormality |
| EF27 |
Hole Punch Unit paper edge detection order abnormality-1 |
| EF28 |
Hole Punch Unit paper edge detection order abnormality-2 |
| F070 |
Communication error between System-CPU and Engine-CPU |
| F090 |
SRAM abnormality on the SYS board |
| F100 |
HDD format error: HDD cannot be initialized normally. |
| F101 |
HDD unmounted: Connection of HDD cannot be detected. |
| F102 |
HDD start error: HDD cannot become ‘Ready’ state |
| F103 |
HDD transfer time-out: Reading/writing cannot be performed in the specified period of time. |
| F104 |
HDD data error: Abnormality is detected in the data of HDD. |
| F105 |
HDD other error |
| F106 |
Point and Print partition damage |
| F107 |
/BOX partition damage |
| F108 |
/SHA partition damage |
| F110 |
Communication error between System-CPU and Scanner-CPU |
| F111 |
Scanner response abnormality |
| F120 |
Database abnormality: Database is not operating normally. |
| F130 |
Invalid MAC address |
| F200 |
Data Overwrite option (GP-1070) disabled |
| F350 |
SLG board abnormality |
| F400 |
SYS board cooling fan abnormality |