| |
|
| Code |
Description |
| C021 |
Developer unit motor-YMC locking error: The developer unit motor-YMC is not rotating normally. |
| C022 |
Developer unit mixer motor-YMC locking error: The developer unit mixer motor-YMC is not rotating normally |
| C023 |
Developer unit motor-K locking error: The developer unit motor-K is not rotating normally. |
| C024 |
Developer unit mixer motor-K locking error: The developer unit mixer motor-K is not rotating normally. |
| C130 |
1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 1st drawer) |
| C140 |
2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 2nd drawer) |
| C150 |
3rd drawer tray abnormality: The 3rd drawer tray-up motor is not rotating or the 3rd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 3rd drawer) |
| C160 |
4th drawer tray abnormality: The 4th drawer tray-up motor is not rotating or the 4th drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 4th drawer) |
| C180 |
LCF tray-up motor abnormality: The LCF tray-up motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF) |
| C1A0 |
LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF) |
| C1C0 |
Option LCF tray-up motor abnormality: The option LCF tray-up motor is not moving normally |
| C260 |
Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON. |
| C270 |
(1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time. (2) Downloading firmware with an incorrect model. |
| C280 |
Carriage home position sensor not turning ON within a specified period of time: The carriage does not reach to its home position in a specified period of time. |
| C360 |
Needle electrode cleaner operation abnormality |
| |
|
| C370 |
Transfer belt operation abnormality |
| C380 |
Auto-toner sensor-K abnormality (upper limit) |
| C381 |
Auto-toner sensor-K abnormality (lower limit) |
| C382 |
Auto-toner sensor-K connection error |
| C390 |
Auto-toner sensor-C abnormality (upper limit) |
| C391 |
Auto-toner sensor-C abnormality (lower limit) |
| C392 |
Auto-toner sensor-C connection error |
| C3A0 |
Auto-toner sensor-M abnormality (upper limit) |
| C3A1 |
Auto-toner sensor-M abnormality (lower limit) |
| C3A2 |
Auto-toner sensor-M connection error |
| C3B0 |
Auto-toner sensor-Y abnormality (upper limit) |
| C3B1 |
Auto-toner sensor-Y abnormality (lower limit) |
| C3B2 |
Auto-toner sensor-Y connection error |
| C3C0 |
Process unit connection error |
| C411 |
Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser belt does not rise in a specified period of time after power is turned ON. |
| |
|
| C412 |
Thermistor/heater lamp abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser belt temperature does not rise within a specified period of time after power-ON. |
| C443 |
Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature) |
| C445 |
Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality) |
| C446 |
Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality) |
| C447 |
Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status) |
| C448 |
Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified |
| C451 |
Thermopile and edge thermistor temperature difference |
| C452 |
Thermopile temperature difference |
| C461 |
Pressure roller heater 40°C detection (Not determined) |
| C462 |
Pressure roller heater 40°C detection (Determined) |
| C463 |
Pressure roller thermistor and edge thermistor temperature difference |
| C464 |
Pressure roller thermistor temperature difference |
| C465 |
Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| C466 |
Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) |
| C467 |
Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status) |
| |
|
| C468 |
Pressure roller thermistor abnormality after entering ready status (overheating) |
| C471 |
IH board initialization abnormality |
| C472 |
Power supply abnormality |
| C473 |
Surge pressure detection / power and voltage upper limit abnormality |
| C474 |
Power and voltage lower limit abnormality |
| C476 |
IH low power supply |
| C480 |
IGBT high temperature abnormality |
| C481 |
IH drive circuit abnormality |
| C490 |
IH circuit abnormality / IH coil abnormality |
| C4B0 |
Fuser unit counter abnormality |
| C4B1 |
Fuser unit voltage judgment abnormality |
| C4D0 |
Fuser belt thermopile abnormality |
| C4E0 |
Fuser unit releasing operation abnormality - Though the pressure roller is released, its position cannot be detected. |
| C4E1 |
Fuser unit contacting operation abnormality - Though the pressure roller is contacted, its position cannot be detected. |
| C4E2 |
Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates. |
| C4E3 |
Fuser motor rotation abnormality |
| C550 |
RADF I/F error: Communication error has occurred between the RADF and the scanner. |
| C560 |
Communication error between Engine-CPU and PFC board |
| C570 |
Communication error between Engine-CPU and CNV board |
| C580 |
Communication error between CNV board and finisher |
| C5A0 |
SRAM board not connected (LGC board) |
| C5A1 |
SRAM board data abnormality (LGC board) |
| C730 |
RADF EEPROM error: Data abnormality occurs during the EEPROM writing of the RADF is performed. |
| C880 |
RADF original feed motor abnormality: An error signal has been detected when the motor is rotating. |
| C890 |
RADF read motor abnormality: An error signal has been detected when the motor is rotating. |
| C8A0 |
RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating. |
| C8B0 |
RADF original exit motor abnormality: An error signal has been detected when the motor is rotating. |
| C8C0 |
RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed, but is ended unsuccessfully. |
| C8E0 |
RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred. |
| C900 |
Connection error between SYS board and LGC board |
| C940 |
Engine-CPU abnormality |
| C962 |
LGC board ID abnormality |
| C970 |
High-voltage transformer abnormality: Leakage of the main charger is detected. |
| C9E0 |
Connection error between SLG board and SYS board |
| CA00 |
Image position alignment abnormality |
| CA10 |
Polygonal motor abnormality: The polygonal motor is not rotating normally |
| CA20 |
H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams. |
| CA47 |
SNS board abnormality: The SNS board does not operate due to disconnection or the harness breaking. |
| CB00 |
Finisher not connected: Communication error has occurred between the equipment and finisher. [MJ1103/1104] |
| CB01 |
Finisher communication error: Communication error has occurred between the equipment and finisher. [MJ-1103/1104] |
| CB10 |
Entrance motor abnormality: The entrance motor is not rotating normally. [MJ-1103/1104] |
| CB11 |
Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1103/1104] |
| CB12 |
Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1103/1104] |
| CB13 |
Finisher exit motor abnormality |
| CB14 |
Paper holding arm motor abnormality |
| |
|
| CB30 |
Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally. [MJ-1103/1104] |
| CB31 |
Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. [MJ-1103/1104] |
| CB40 |
Rear aligning plate motor abnormality: Rear aligning plate motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally. [MJ-1103/ 1104] |
| CB50 |
Stapler home position error: The stapler home position sensor does not work. [MJ-1103/1104] |
| CB51 |
Stapler shift home position error: The stapler is not at the home position. [MJ-1103/1104] |
| CB60 |
Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally. [MJ-1103/1104] |
| CB80 |
Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON |
| CB81 |
Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1103/1104] |
| CB82 |
Finisher - Main CPU program error |
| CB83 |
Saddle Stitch Finisher - Main CPU program error |
| CB84 |
Hole Punch Unit - Main CPU program error |
| CB91 |
Saddle Stitch Finisher flash ROM abnormality |
| CB92 |
Saddle Stitch Finisher RAM abnormality |
| CB93 |
Additional folding motor abnormality |
| CB94 |
Saddle transport motor abnormality |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| |
|
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| |
|
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| |
|
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| |
|
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CB95 |
Stacker motor abnormality |
| CBA0 |
Stitch motor (front) abnormality: Stitch motor (front) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBB0 |
Stitch motor (rear) abnormality: Stitch motor (rear) is not rotating or rotary cam is not moving normally. [MJ-1103/1104] |
| CBC0 |
Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1103/1104] |
| CBE0 |
Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1103/1104] |
| CC20 |
Communication error between finisher and saddle stitcher: Communication error between finisher controller PC board and saddle stitcher controller board [MJ-1103/1104] |
| CC30 |
Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1103/1104] |
| CC31 |
Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1103/1104] |
| CC41 |
Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ1103/1104] |
| CC51 |
Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC52 |
Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC60 |
Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ1103/1104 (when MJ-6102 is installed)] |
| CC61 |
Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1103/1104 (when MJ-6102 is installed)] |
| CC71 |
Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| CC72 |
Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1103/ 1104 (when MJ-6102 is installed)] |
| EAD0 |
Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing. |
| EAE0 |
Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher. |
| EB30 |
Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing. |
| EB50 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper. |
| EB60 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]). |
| ED10 |
Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1103/1104 (when MJ-6102 is installed)] |
| ED11 |
Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1103/1104 (when MJ6102 is installed)] |
| ED12 |
Shutter home position error: The shutter is not at the home position. [MJ-1103/1104] |
| ED13 |
Front alignment plate home position error: The front alignment plate is not at the home position. [MJ1103/1104] |
| ED14 |
Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ1103/1104] |
| ED15 |
Paddle home position error: The paddle is not at the home position. [MJ-1103/1104] |
| ED16 |
Buffer tray home position error: The buffer tray is not at the home position. [MJ-1103/1104] |
| EF10 |
Paper not supported for Saddle Stitch Finisher |
| EF11 |
Saddle Stitch Finisher stapling error (front) |
| EF12 |
Saddle Stitch Finisher stapling error (rear) |
| EF13 |
Saddle paper holder home position detection abnormality |
| EF14 |
Saddle paper exit jam |
| EF15 |
Saddle Stitch Finisher side alignment motor home position detection abnormality |
| EF16 |
Saddle Stitch Finisher stacker motor home position detection abnormality |
| EF17 |
Saddle Stitch Finisher folding blade home position detection abnormality |
| EF18 |
Saddle Stitch Finisher additional folding roller home position detection abnormality |
| EF19 |
Saddle paper folding jam |
| EF20 |
Saddle stacker jam |
| EF21 |
Hole Punch Unit paper leading edge skew detection abnormality |
| EF22 |
Hole Punch Unit paper leading edge detection abnormality |
| EF23 |
Hole Punch Unit paper alignment abnormality |
| EF24 |
Hole Punch Unit paper trailing edge skew detection abnormality |
| EF25 |
Hole Punch Unit paper trailing edge detection abnormality |
| EF27 |
Hole Punch Unit paper edge detection order abnormality-1 |
| EF28 |
Hole Punch Unit paper edge detection order abnormality-2 |
| EAD0 |
Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing. |
| EAE0 |
Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher. |
| EB30 |
Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing. |
| EB50 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper. |
| EB60 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]). |
| ED10 |
Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1103/1104 (when MJ-6102 is installed)] |
| ED11 |
Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1103/1104 (when MJ6102 is installed)] |
| ED12 |
Shutter home position error: The shutter is not at the home position. [MJ-1103/1104] |
| ED13 |
Front alignment plate home position error: The front alignment plate is not at the home position. [MJ1103/1104] |
| ED14 |
Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ1103/1104] |
| ED15 |
Paddle home position error: The paddle is not at the home position. [MJ-1103/1104] |
| ED16 |
Buffer tray home position error: The buffer tray is not at the home position. [MJ-1103/1104] |
| EF10 |
Paper not supported for Saddle Stitch Finisher |
| EF11 |
Saddle Stitch Finisher stapling error (front) |
| EF12 |
Saddle Stitch Finisher stapling error (rear) |
| EAD0 |
Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing. |
| EAE0 |
Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher. |
| EB30 |
Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing. |
| EB50 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper. |
| EB60 |
Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]). |
| ED10 |
Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1103/1104 (when MJ-6102 is installed)] |
| ED11 |
Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1103/1104 (when MJ6102 is installed)] |
| ED12 |
Shutter home position error: The shutter is not at the home position. [MJ-1103/1104] |
| ED13 |
Front alignment plate home position error: The front alignment plate is not at the home position. [MJ1103/1104] |
| ED14 |
Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ1103/1104] |
| ED15 |
Paddle home position error: The paddle is not at the home position. [MJ-1103/1104] |
| ED16 |
Buffer tray home position error: The buffer tray is not at the home position. [MJ-1103/1104] |
| EF10 |
Paper not supported for Saddle Stitch Finisher |
| EF11 |
Saddle Stitch Finisher stapling error (front) |
| EF12 |
Saddle Stitch Finisher stapling error (rear) |
| F200 |
Data Overwrite option (GP-1070) disabled |
| F350 |
SLG board abnormality |
| F400 |
SYS board cooling fan abnormality |