| Kod |
Açıklama |
Sebepler |
| 30 |
FAX kontrol PWB sistemi hatası |
Arızalı FAX kontrol PWB. |
| Bir donanım problemi nedeniyle faks yazılımı ile işleme tabi tutulamadı. |
| 60 |
Motor PWB tipi hata |
Arızalı motor alt PCB. |
| 70 |
FAX kontrolü PWB uyumsuz algılama hatası FAX kontrolünün |
Arızalı FAX yazılımı |
| anormal tespiti PWB uyumsuzluğu FAKS kontrol PWB ile ilk iletişimde herhangi bir normal iletişim komutu iletilmez. |
Arızalı FAX kontrol PWB. |
| 100 |
Yedek bellek aygıtı hatası |
Arızalı flaş belleği. |
| 120 |
MAC adresi veri hatası |
Ana PWB arızalı. |
| MAC adresinin geçersiz olduğu veriler için. |
Arızalı flaş belleği. |
| |
Arızalı motor PWB. |
| 130 |
Yedek bellek okuma / yazma hatası (ana PWB) |
Arızalı flaş belleği. |
| Ana PWB arızalı. |
| 140 |
Yedek bellek veri hatası (ana PWB) |
Arızalı flaş belleği. |
| Ana PWB arızalı. |
| 150 |
Yedek bellek okuma / yazma hatası (motor PWB) |
Yanlış kurulum motoru PWB EEPROM. |
| Algılama motor PWB EEPROM iletişim hatası. |
Arızalı motor PWB. |
| |
EEPROM'un cihaz hasarı. |
| 160 |
Yedekleme belleği veri hatası (motor PWB) |
Arızalı flaş belleği. |
| Arızalı motor PWB. |
| 170 |
Faturalama sayımı hatası |
EEPROM'un veri hasarı. |
| Faturalama sayaçlarının ana ve motor yedekleme belleğinde bir sağlama toplamı hatası tespit edildi. |
Arızalı PWB. |
| 180 |
Makine numarası uyuşmazlığı |
EEPROM'un veri hasarı. |
| Ana makine numarası ve motor numarası uyuşmuyor . |
| 320 |
G / Ç CPU iletişim hatası |
Arızalı PWB. |
| Bir iletişim hatası art arda 10 kez algılanıyor. |
| 630 |
DMA hatası Görüntü verilerinin DMA iletimi, belirtilen süre içinde tamamlanmıyor. |
Konektör terminallerindeki temassızlık. Ana PWB arızalı. |
| 800 |
Resim işleme hatası |
Ana PWB arızalı. |
| JAM05 iki kez algılanır. |
| 830 |
FAX kontrol PWB flaş program bölgesi sağlama toplamı hatası |
Arızalı FAX yazılımı. |
| Bir flaş toplama hatası , faks kontrol PWB'nin programı ile oluştu. |
Arızalı FAX kontrol PWB. |
| 840 |
RTC Hataları |
Akünün ana PWB bağlantısı kesildi. |
| Zaman, RTC zamanının karşılaştırılmasına dayanarak geri dönmeye karar verilir ve şu anki zaman veya beş yıl veya daha fazla süre geçti. |
Ana PWB arızalı. |
| 870 |
FAX kontrol PWB, ana PWB yüksek |
Yanlış kurulum FAX kontrol PWB. |
| kapasiteli veri aktarım hatasına FAX kontrolü PWB ve makinenin ana PWB'si arasındaki yüksek kapasiteli veri aktarımı, veri aktarımı belirtilen zamanlarda tekrar dense bile normal olarak gerçekleştirilemedi. |
Arızalı FAX kontrol PWB veya ana PWB. |
| 920 |
Faks dosya sistemi hatası |
Arızalı FAX kontrol PWB. |
| FAX kontrol PWB'inin flash belleğinin dosya sistemi anormalliği için yedek veri tutulmaz. |
| 1010 |
Motor hatasını |
Kasetteki kusurlu taban plakası yükseltme mekanizması. |
| kaldırma Kaset 1 takıldıktan sonra kaldırma sensörü 12 saniye içinde açılmıyor. Bu hata art arda dört kez algılanır. |
Konektör kablosunda arızalı veya konnektördeki zayıf kontak. |
| |
Kaldırma motorunun arızalı tahrik sistemi. |
| |
Arızalı kaldırma motoru. |
| |
Arızalı motor PWB. |
| 1020 |
PF kaldırma motoru hatası (kağıt besleyici) |
Kasetteki kusurlu taban plakası yükseltme mekanizması. |
| Kaset 2 takıldıktan sonra PF kaldırma sensörü 1 12 saniye içinde açılmıyor. Bu hata art arda dört kez algılanır. |
Konektör kablosunda arızalı veya konnektördeki zayıf kontak. |
| |
PF kaldırma motorunun arızalı tahrik sistemi 1. |
| |
Arızalı PF kaldırma motoru 1. |
| |
Arızalı PF ana PWB. |
| 1030 |
PF kaldırma motoru hatası (kağıt besleyici) |
Kasetteki kusurlu taban plakası yükseltme mekanizması. |
| Kaset 3 takıldıktan sonra PF kaldırma sensörü 2 12 saniye içinde açılmıyor. Bu hata art arda dört kez algılanır. |
Konektör kablosunda arızalı veya konnektördeki zayıf kontak. |
| |
PF kaldırma motorunun arızalı tahrik sistemi 2. |
| |
Arızalı PF kaldırma motoru 2. |
| |
Arızalı PF ana PWB. |
| 1800 |
Kağıt besleyici iletişim hatası |
Yanlış kurulum kağıt besleyicisi. |
| Bir iletişim hatası art arda 10 kez algılanıyor. |
Konektör kablosunda arızalı veya konnektördeki zayıf kontak. |
| |
Arızalı motor PWB. |
| |
Arızalı PF ana PWB. |
| 1900 |
Kağıt |
Arızalı PF ana PWB. |
| besleyici EEPROM hatası Veri yazarken, yazma verileri ve okunan veriler sürekli olarak 5 kez mutabık değildir. |
EEPROM'un cihaz hasarı. |
| 2000 |
Ana motor sabit durum hatası |
Konektör kablosunda arızalı veya konnektördeki zayıf kontak. |
| Ana motor stabilize olduktan sonra 1 sn süreyle sürekli KAPALI tespit edildi. |
Ana motorun arızalı tahrik sistemi. |
| |
Ana motor arızalı. |
| |
Arızalı motor PWB. |
| 2010 |
Main motor drive error |
Defective connector cable or poor contact in the connector. |
| The main motor is not stabilized within 2 s after driving starts. |
Defective drive transmission system of the main motor. |
| |
Defective main motor. |
| |
Defective engine PWB. |
| 2600 |
PF drive motor error (paper feeder) |
Defective connector cable or poor contact in the connector. |
| When the PF drive motor is driven, error signal is detected continuously for 1 s. |
Defective drive transmission system of the PF drive motor. |
| |
Defective PF drive motor. |
| |
Defective PF main PWB. |
| 3100 |
ISU home position error |
Defective connector cable or poor contact in the connector. |
| The home position is not correct when the power is turned on or at the start of copying using the table. |
Defective home position sensor. |
| |
Defective ISU motor. |
| |
Defective CCD PWB. |
| |
Defective engine PWB. |
| 3200 |
Exposure lamp error |
Defective connector cable or poor contact in the connector. |
| When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s. |
Defective exposure lamp. |
| |
Defective CCD PWB. |
| |
Defective main PWB. |
| 3500 |
Communication error between scanner and ASIC |
Defective connector cable or poor contact in the connector. |
| An error code is detected 3 times in succession. |
Defective CCD PWB. |
| |
Defective main PWB. |
| 3600 |
Scanner sequence error |
Defective main PWB or engine PWB. |
| 4000 |
Polygon motor synchronization error |
Defective connector cable or poor contact in the connector. |
| The polygon motor is not stabilized within 10 s after driving starts. |
Defective polygon motor. |
| |
Defective engine PWB. |
| 4010 |
Polygon motor steady-state error |
Defective connector cable or poor contact in the connector. |
| Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
Defective polygon motor. |
| |
Defective engine PWB. |
| 4100 |
BD initialization error |
Defective connector cable or poor contact in the connector. |
| BD is not detected within 1 s after polygon motor stabilized. |
Defective APC PWB. |
| |
Defective BD PWB. |
| |
Defective main PWB. |
| 4700 |
VIDEO ASIC device error |
Defective connector cable or poor contact in the connector. |
| Defective main PWB or engine PWB. |
| 6000 |
Broken fuser heater wire |
Defective connector cable or poor contact in the connector. |
| The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less. |
Deformed connector pin. |
| |
Defective triac. |
| |
Fuser thermostat triggered. |
| |
Broken fuser heater wire. |
| |
Defective engine PWB. |
| 6000, 6020, 6030, 6050 |
Broken fuser heater wire |
Deformed connector pin. |
| Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature |
Defective triac. |
| 6020 |
Abnormally high fuser thermistor temperature |
Deformed connector pin. |
| The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms. |
Defective triac. |
| |
Shorted fuser thermistor. |
| |
Defective engine PWB. |
| 6030 |
Broken fuser thermistor wire |
Defective connector cable or poor contact in the connector. |
| A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up. |
Deformed connector pin. |
| |
Defective triac. |
| |
Defective fuser thermistor. |
| |
Defective engine PWB. |
| 6050 |
Abnormally low fuser thermistor temperature |
Deformed connector pin. |
| As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second. |
Defective triac. |
| |
Defective fuser thermistor |
| |
Defective fuser heater. |
| |
Defective engine PWB. |
| 6400 |
Zero-cross signal error |
Defective connector cable or poor contact in the connector |
| While fuser heater control is performed, the zero-cross signal is not input within 3 s. |
Defective power source PWB or engine PWB. |
| 7800 |
Broken external thermistor wire |
Defective connector cable or poor contact in the connector. |
| The thermistor output value is 0.3 V or less. |
Defective temperature sensor. |
| 7810 |
Short-circuited external thermistor wire |
Defective connector cable or poor contact in the connector. |
| The thermistor output value is 3 V or more. |
Defective temperature sensor. |
| 7900 |
Drum unit EEPROM error |
Defective connector cable or poor contact in the connector. |
| No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
Defective drum unit. |
| 7910 |
Developer unit EEPROM error |
Defective connector cable or poor contact in the connector. |
| No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
Defective developer unit. |
| 8030 |
Tray upper limit detection problem (document finisher) |
Defective connector cable or poor contact in the connector. |
| When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected. |
Defective tray upper limit sensor, paper surface sensor 1/2. |
| |
Defective DF main PWB. |
| 8040 |
Belt problem (document finisher) |
Defective connector cable or poor contact in the connector. |
| The belt sensor does not turn on/off within specified time of the belt solenoid turning on. |
Defective belt sensor. |
| |
Defective belt solenoid. |
| |
Defective DF main PWB. |
| 8140 |
Tray elevation motor problem (document finisher) |
Defective connector cable or poor contact in the connector. |
| The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated. |
Defective connector cable or poor contact in the connector. |
| |
The tray elevation motor malfunctions. |
| |
Defective tray lower limit sensor, paper surface sensor 1/2. |
| |
Defective DF main PWB. |
| 8210 |
Stapler problem (document finisher) |
Defective connector cable of staple or poor contact in the connector. |
| Jam 7012 or 7023 is indicated. |
The stapler is blocked with a staple. |
| |
The stapler is broken |
| |
Defective DF main PWB. |
| 8320 |
Adjustment motor 2 problem (document finisher) |
Defective connector cable or poor contact in the connector. |
| The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on. |
Defective adjustment sensor 2. |
| |
Defective adjustment motor 2. |
| |
Defective DF main PWB. |
| 8330 |
Adjustment motor 1 problem (document finisher) |
Defective connector cable or poor contact in the connector. |
| The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on. |
Defective adjustment sensor 1. |
| |
Defective adjustment motor 1. |
| 8350 |
Roller motor problem (document finisher) |
Defective DF main PWB. |
| The roller sensor does not turn on/off within specified time of the roller motor turning on. |
Defective connector cable or poor contact in the connector. |
| |
Defective roller sensor. |
| |
Defective roller motor. |
| |
Defective DF main PWB. |
| 8360 |
Slide motor problem (document finisher) |
Defective connector cable or poor contact in the connector. |
| The slide sensor does not turn on/off within specified time of the slide motor turning on. |
Defective slide sensor. |
| |
Defective slide motor. |
| |
Defective DF main PWB. |
| 8460 |
EEPROM problem (document finisher) |
Defective EEPROM or DF main PWB. |
| Reading from or writing to EEPROM cannot be performed. |
| 8800 |
Document finisher communication error |
Defective connector cable or poor contact in the connector |
| A communication error is detected 10 times in succession. |
Defective DF main PWB. |
| |
Defective engine PWB. |
| 8830 |
Bridge communication error (document finisher) |
Defective connector cable or poor contact in the connector. |
| A communication error is detected 10 times in succession. |
Defective bridge PWB. |
| |
Defective engine PWB. |
| 8990 |
Document finisher communication error |
Defective connector cable or poor contact in the connector. |
| Defective DF main PWB. |
| Defective bridge PWB. |
| 9000 |
Document processor communication error |
Defective connector cable or poor contact in the connector. |
| A communication error is detected 10 times in succession. |
Defective DP main PWB. |
| 9060 |
DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. |
Defective DP main PWB. |
| Device damage of EEPROM. |
| 9500 |
BRU communication error |
IPU PWB error |
| 9510 |
BRU PWB error |
IPU PWB error |
| 9520 |
BRU PWB data error |
IPU PWB error |
| 9530 |
Machine No.backup error C |
IPU PWB error |
| 9540 |
Machine No.backup error D |
IPU PWB error |
| 9550 |
Machine No.backup error E |
IPU PWB error |
| F000 |
Main PWB - operation panel PWB communication error |
Defective main PWB. |
| Defective operation panel PWB. |
| F010, F011, F012, F013 |
Main PWB checksum error |
Defective main PWB. |
| F040 |
Main PWB - print engine communication error |
Defective main PWB. |
| Defective engine PWB. |
| F050 |
Print engine ROM checksum error |
Defective engine PWB. |